Victony AC1200 Extender Setup

With the Victony AC1200 Extender Setup , you’re entering a world of better connectivity! With our cutting-edge extender, you can quickly improve the speed and range of your wireless network. The AC1200 Extender will improve your home or office networking experience. Our technology addresses dead zones, weak connections, and insufficient coverage, resulting in increased connectivity.

Manual Method: Setting up Victony AC1200 Extender 

steps by step instruction for Victony AC1200 extender setup:

1. Connect the extender to a power source.
2. Please wait until the power LED becomes a steady solid blue.
3. For about 2 seconds, press and hold the WPS button on the extension. 
4. Pressing and holding the WPS button on the router for around 2 seconds.
5. The LED lights on the extender will start blinking. 
6. Once the LED lights on the extender turn solid blue, the extender is successfully connected to the router.

You have successfully manually configured your Victony AC1200 WiFi extender.

Keep in mind that these instructions are general and may vary slightly based on the specific model and firmware version of your extender. For precise instructions tailored to your device, it is recommended to consistently consult the user manual provided by Victony.

How to Configure Your Victony AC1200 Extender using WPS ?

If your extender does not support WPS, you can configure it using a web browser. The following are the necessary steps:

1. Connect your PC to the extender’s WiFi network.
2. Open a web browser and type the IP address of the extender in the address bar. The default IP address is 192.168.10.1.
3. Enter the username and password for the extender. By default, both the username and password are set to “admin”.
4. Select the “Repeater” mode.
5. Enter the SSID and password for your WiFi network.
6. Click on the “Connect” button.

You have successfully used WPS to configure your Victony AC1200 extender. Keep in mind that the extender may have additional features accessible via a web interface, so you may want to study those settings to fine-tune your extended network setup as needed.

Factory Resetting the Victony AC1200 Extender 

To perform a factory reset on your Victony AC1200 extender, you can follow the following basic instructions.

• On your Victony AC1200 Extender, locate the reset button.
• Ensure that you have turned on the extender and connected it to an electrical outlet.
• Press and hold the reset button for around 10 seconds with a tiny, pointed item such as a paperclip.
• After holding the reset button, release it.
• The extender will restart and revert to its factory settings.
• After the reset, you must reconnect the extender to your WiFi network and make any necessary changes.

It is important to note that a factory reset will wipe all of the extender’s settings, including the WiFi network name and password. You must reinstall the extender from scratch.

How to Update the firmware on the Victony AC1200 extender?

To upgrade the firmware of your Victony AC1200 extender, you can proceed with the following steps:

1. Establish a connection between your computer and the extender’s WiFi network.
2. Open a web browser and type the IP address of the extender in the address bar. The default IP address is 192.168.10.1.
3. Provide the extender’s default username and password, which are both set to “admin.”
4. Press on the “Management” tab.
5. Click the “Firmware Update” button.
6. Tap on the “Check for Updates” button.
7. If there is a newer firmware available, click on the “Download and Install” button.
8. The extender will now download and install the new firmware.
9. Once the firmware update is complete, the extender will reboot.

Always download the firmware from the official Victony website to avoid compatibility issues or security threats. If you are unsure about upgrading the firmware manually, contact Victony’s customer care.

Troubleshooting Tips:

Victony AC1200 Extender Setup involves a series of steps to ensure that it works correctly. If you’re facing issues during the setup process or with the extender’s performance, follow these troubleshooting steps:

• Connect the extender to a power outlet close to your router.
• Please wait until the power LED becomes steady.
• Ensure you’re connecting to the correct WiFi network (e.g., “Victony_Extender”).
• Use the default WiFi password if you haven’t changed it.
• Position the extender halfway between your router and the area with weak WiFi.
• Avoid obstructions like walls, mirrors, and metal objects.
• Press and hold the reset button for 10 seconds to reset the extender to its default settings.
• Launch a web browser and type the default IP address into the address bar.
• Log in with the username and password.
• Follow the setup wizard to connect the extender to your existing WiFi network.
• Provide the WiFi SSID and password of your main router.
• If the wizard doesn’t work, manually configure the extender settings.
• Set the SSID and password identical to your main router.
• Ensure the extender is using the same WiFi security settings (WPA/WPA2).
• Use a different WiFi channel for the extender if you experience interference.
• Check for firmware updates on the Victony website and update if necessary.
• Ensure your devices are compatible with the 2.4GHz or 5GHz frequency band the extender is broadcasting.
• Understand the extender’s limitations. It may not provide full coverage for a large area.
• Double-check all settings and passwords for typos or mistakes.
• Use a WiFi analyzer app to measure signal strength and optimise placement.
• Occasionally, reboot both the router and extender to resolve connectivity issues.
• If all else fails, contact Victony customer support for further assistance.

If you are still having troubles after following these suggestions, you can contact the extender’s manufacturer for further assistance.

You can also visit the Victony website for troubleshooting advice and frequently asked questions.

I hope these suggestions assist you in troubleshooting your Victony AC1200 extender setup issues.